Reer Changing Table Heater 2 in 1 FeelWell with 2 heat settings incl. 10-pack muslin washcloths - White Grey

WARNING AND SAFETY INSTRUCTIONS

Safety instructions
! Follow the instructions in the manual, otherwise there is a risk that the changing table radiant heater may be damaged. In the worst case, your child, yourself or other people may be put at risk or injured.

Safety instructions when putting into operation
• This device is not suitable as a main heating device!
• The device must not be used in small rooms occupied by persons who cannot leave the room independently.
• Please use the item only for its intended purpose.
• Use the device exclusively for private use; it is not intended for commercial use.
• Improper use will result in loss of warranty claims.
• Do not use the device outdoors.
• Remove all packaging materials before use.
• Check the device for obvious damage before each use. Do not use the device if it or the power cord is damaged.
• Check that the information on the rating plate matches your mains voltage.
• Do not expose the device to mechanical shocks.
• Do not move the device during operation!
• Repairs may only be carried out by a qualified professional. Improper repairs can pose significant hazards to the user – this also applies to replacing the power cord.

Warnings
Risk of burns / fire hazard:
• Do not cover! Never place anything on the device, even when it has cooled down.
• Observe minimum distances! Position the device at least 65 cm away from flammable materials such as wood, textiles, etc. The distance from the heater to the ceiling of at least 35 cm must be strictly observed.
• Only connect directly to the mains socket. Do not connect any control devices such as timers, remote controls, etc. to the device.
• Keep the power cord away from all hot parts of the device, including power cords of neighbouring electrical devices.
• Failure to observe these instructions poses a fire hazard! For emergencies, make sure in advance where the nearest fire extinguisher is located. In case of fire, immediately unplug the device and extinguish the fire.

Danger
• Do not immerse the device or the power plug in water, other liquids or flammable cleaning agents to avoid the risk of electric shock and/or fire hazard.
• Risk of electric shock! Do not use the device near bathtubs, showers, washbasins or other containers filled with water. Never touch the power plug or device with wet hands! Proximity to water remains hazardous even when the device is switched off.

Warning:
• The device must never be used unsupervised.
• The maximum irradiation time must not exceed 15 minutes. Infants with elevated temperature must not be irradiated. There is a risk of overheating the body.
• Avoid additional heat exposure such as sunlight or additional radiation sources, as this can increase your baby’s body temperature.
• The irradiation distance of 100 cm from the heater to the table must be strictly observed.
• This device is not equipped with a room temperature control device. The heater must not be used in small rooms occupied by persons who cannot leave the room independently.
• This product is not a toy! Do not allow children to play with the device.
• Risk of strangulation! To prevent strangulation with the power cord, secure the cables out of the reach of children.
Caution:
• Risk of injury: do not touch the device during operation.
• Do not use the device within reach of children. Secure the power cord and ensure that it is not accidentally pulled, causing the device to fall.
• Persons (including children) who due to their physical, sensory or mental abilities, or lack of experience or knowledge, are not able to use the device safely should not use the device without supervision or instruction by a responsible person.
C Assembly with stand
A drawing describing this can be found on the first pages.
1. Insert the 5 feet (A2) into the foot socket system (A1).
2. Place the foot cover (A3) over it.
3. Insert the lower plug tube (A4) into the opening.
4. Secure the lower plug tube from below with the plastic screw (A5).
5. Slide a cable holder (A7) over the lower plug tube.
6. Insert the middle plug tube (A8) with the slot as shown onto the lower plug tube and turn the middle plug tube until the holes of both tubes align. Secure the middle plug tube with the supplied screw using a Phillips screwdriver.
7. Slide the remaining cable holders over the middle tube and insert the upper plug tube (A9) onto the middle plug tube. Secure the upper plug tube (A9) with the supplied screw using a Phillips screwdriver.
8. Remove the wall bracket from the device.
9. Now place the changing table radiant heater (A10) on the stand and secure it with the plastic screw (A6).
10. Open the grey locking screw of the upper plug tube and set the desired height of the changing table radiant heater with the telescopic rod. Ensure the distance to the changing table of 100 cm is maintained. Secure the height by closing the locking screw.
11. Secure the cable in the cable holders.
12. Place the changing table radiant heater at the desired location, taking into account the minimum distances in the room and out of reach of children. Ensure the stand is stable and on a flat surface.
Note: If fewer than 5 feet are installed (e.g. for space reasons), the user must otherwise ensure the stability of the changing table radiant heater. Never place the changing table radiant heater freely in the room with fewer than 5 feet! Place the changing table radiant heater at the desired location, taking into account the minimum distances in the room and out of reach of children. Ensure the stand is stable and on a flat surface.
D Wall mounting
1. Remove the mounting plate from the device as shown.
2. Hold the wall bracket against the wall considering the minimum distances and mark the screw holes with a pencil. Use a spirit level for horizontal alignment.
3. Screw the wall bracket to the wall with the supplied screws and plugs.
4. Insert the changing table radiant heater into the designated slots of the wall bracket.
5. Screw the changing table radiant heater to the wall bracket with the previously removed screws (D1).
! Safety instructions for wall mounting:
• The changing table radiant heater may only be mounted fixed and horizontally on the wall. Ceiling mounting is not permitted!
• The changing table heater must not be mounted on wood, plastic or other flammable materials, or below sockets.
E Putting into operation
1. Plug the power plug into the socket.
2. Pull the cord to switch on the radiant heater. The radiant heater can be set to two heating levels, 400 W (level “1”) and 800 W (level “2”).
3. By pulling the cord again, the heating level can be changed or the device switched off again (level “0”).
F Automatic switch-off function
1. To activate the automatic switch-off function, set the timer switch on the underside of the device to “ON”. The device switches off automatically after 10 minutes.
2. To switch the device on again after the automatic switch-off, you have 2 options:
• Switch the switch to “Off” or
• Pull the cord until the heating level indicator shows “0”. Pulling again to heating level “1” or “2” will switch the device on again.
Tilt switch-off function
The device has an automatic tilt switch-off function. If the angle exceeds 25° (e.g. if the stand falls over or in ceiling mounting), the device switches off automatically.
Warning: When the device is set upright, the radiant heater switches on automatically again.
Troubleshooting
Problem possible causes What to do?
No radiant heat despite heating level indicator “1” or “2”.
• The power plug is not properly inserted.
• The automatic switch-off function (timer) is activated.
• The automatic tilt switch-off function is activated because the angle of the radiant heater exceeds 25°.
• Check the power plug.
• Switch the “Timer” to “Off” or switch the device off and on again by repeatedly pulling the cord.
• Ensure the radiant heater is mounted horizontally and fixed to the wall or that the stand is upright.
Cleaning, maintenance
Before cleaning, make sure the device is switched off and cooled down (unplug the power plug). Clean the surface with a dry or slightly damp cloth. Have the reflector and heating rods cleaned only by a professional. The device is not waterproof and must not be immersed in water or exposed to direct moisture. This product requires no special maintenance. Repairs to the device may only be carried out by a professional.
Environmental protection notes
Electronic waste devices are raw materials and must not be disposed of in household waste, but must be taken to a collection point for recycling electrical devices. Consumers are legally obliged to dispose of electrical waste properly. By reusing, material recycling or other forms of recycling of old devices, you make an important contribution to protecting our environment. Please ask your local authority for the responsible disposal site. The adjacent symbol indicates the obligation for proper disposal.
Warranty
Please keep the purchase receipt, user manual and article number. Warranty claims or claims from warranty promises are to be handled exclusively with the dealer. All technical data, information and properties of the product described in this manual have been compiled to the best of our knowledge and correspond to the status at the time of publication. The information provided by reer should be correct and reliable. However, reer assumes no liability for possible errors in this document and reserves the right to make changes to the product design or specifications without prior notice.
Copyright notes
Reproduction and distribution of information from this copyright-protected work in any form or by any means, graphic, electronic or mechanical, by photocopying, recording on tape or storing in a data retrieval system, even in part, require prior written permission from reer.
Remove all bags and packaging materials before use.